CONFIGURATION OSPF ROUTEUR CISCO PDF

This of course leads to more complexity in the configuration and troubleshooting of OSPF networks. Administrators that are used to the. This document shows sample configurations for Open Shortest Path First (OSPF) authentication which allows the flexibility to authenticate. router-id-ospf. Command Default. If this command is not configured, OSPF chooses an IPv4 address as the router ID from one of its interfaces.

Author: JoJojinn Faern
Country: Guatemala
Language: English (Spanish)
Genre: Spiritual
Published (Last): 9 June 2017
Pages: 415
PDF File Size: 12.45 Mb
ePub File Size: 5.80 Mb
ISBN: 504-3-11185-175-9
Downloads: 49949
Price: Free* [*Free Regsitration Required]
Uploader: Yozshulabar

Gateway of last resort is not set. Here we can see that 4. Process 2Nbr 4.

Therefore, both should act in the same way, or am I wrong? Hi roger thanks this was great explanation. Virtual routing and forwarding VRF is a technology included in IP Internet Protocol that allows multiple instances of a routing table to co-exist in a router and work together but not interfere with each other.

I have updated the tutorial and it is now complete, please review the last steps again and let me know if you get any issues.

Connect GNS3 to the Internet (local server) – GNS3

Configure the device interfaces. You could show the routing table here, but the fact that you can ping between the loopbacks is verification enough and it is safe to move on. RED is shown and the routes to R4 are now visible with 4. Label 20 Exp 0 ] 16 msec 40 confituration 16 msec. R3 sh ip route vrf RED. Would you mind send me the Ospff config files for this lab please?

  ENFERMEDADES FEBRILES EXANTEMATICAS PDF

LDP is enabled on all the internal interfaces. Ateet, I have updated the tutorial and it is now complete, please review the last steps again and let me know if you get any issues.

What is difference between ABR and ASBR in OSPF network?

Im interested in the troubleshooting, where can I find this? So to review we have now configured IP addresses on the MPLS core, enabled OSPF and full IP connectivity between all routers and finally enabled mpls on all the interfaces in the core and have established ldp neighbors between all routers. Cosco sh mpls ldp neigh. When referring to a higher IP address, step back and look at the IP address as a whole number. Junos OS selects a router identifier according to the following set of rules:.

Example: Configuring an OSPF Router Identifier

The Router-ID uniquely identifies a router in an autonomous system, no two routers in an OSPF autonomous system can have the same router-id. You can see here that we do have a bgp vpnv4 peering to R3 — looking at the PfxRcd you can see it says 0 this is because we have not got any routes in BGP. Here you can see Routing Table: I am Oussema from Tunisia and I have found this tutorial very useful for me.

  CLSI 2013 M100 S23 PDF

It will use the local site addressing of The router ID fields are clearly marked in the output. Establish a console session with devices R1, R2, R3, R4, R5 and SW1 than load the initial configurations provided below by copying the config from the textbox and pasting it into the respected routers console. BGP router identifier 1. First bring 3 routers into your topology R1, Configuragion, R3 position them as below.

Process 2, Nbr 4. R1 sh bgp vpnv4 unicast all summary BGP router identifier 1.

R3 sh ip bgp vpnv4 vrf RED. The router id is used in several OSPF related commands such as the specifying a specific neighbor when clearing a neighbor relationship or when viewing neighbor parameters by using the show ip ospf neighbor rid.

You have to use a routing touteur for the loopbacks. The initial config lists setting it with a For this tutorial we will be using the second option, so go int the ospf process and enter mpls ldp autoconfig — this will enable mpls label distribution protocol on every interface running ospf under configkration specific process.